![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
CONTENTS #contents ---- Lastmodified &lastmod; ---- *Areca [#ga528b05] http://dokuosan.net/zousan/nikki105.html http://www.kuji-clinic.info:81/ **dmesg [#e42ea669] arcmsr0: <Areca SATA 3G Host Adapter RAID Controller arcmsr version 1.20.00.28 2013-09-13 > mem 0xe0600000-0xe0600fff,0xe0000000-0xe03fffff irq 18 at device 14.0 on pci2 Areca RAID adapter0: ARC-1210 F/W version V1.46 2008-08-06 atapci1: <Intel ICH8 SATA300 controller> port 0x2438-0x243f,0x2454-0x2457,0x2430-0x2437,0x2450-0x2453,0x2410-0x241f,0x2400-0x240f irq 19 at device 31.2 on pci0 ata3: <ATA channel> at channel 0 on atapci1 ata4: <ATA channel> at channel 1 on atapci1 atapci2: <Intel ICH8 SATA300 controller> port 0x2428-0x242f,0x244c-0x244f,0x2420-0x2427,0x2448-0x244b,0x20f0-0x20ff,0x20e0-0x20ef irq 19 at device 31.5 on pci0 ata5: <ATA channel> at channel 0 on atapci2 ata6: <ATA channel> at channel 1 on atapci2 pass1 at arcmsr0 bus 0 scbus0 target 16 lun 0 pass1: <Areca RAID controller R001> Fixed Processor SCSI-0 device da0 at arcmsr0 bus 0 scbus0 target 0 lun 0 da0: <Areca ARC-1210-VOL#00 R001> Fixed Direct Access SCSI-5 device da0: Serial Number 0000000442740780 da0: 250.000MB/s transfers (125.000MHz, offset 32, 16bit) da0: Command Queueing enabled da0: 228881MB (468749312 512 byte sectors: 255H 63S/T 29178C) ** smartctl [#u4453142] # smartctl -a --device=areca,3/1 /dev/arcmsr0 -T permissive smartctl 6.4 2015-06-04 r4109 [FreeBSD 9.3-RELEASE-p24 amd64] (local build) Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org Read Device Identity failed: Input/output error === START OF INFORMATION SECTION === Device Model: [No Information Found] Serial Number: [No Information Found] Firmware Version: [No Information Found] Device is: Not in smartctl database [for details use: -P showall] ATA Version is: [No Information Found] Local Time is: Thu Sep 3 18:02:45 2015 JST SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported. SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMART is enabled. A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. # smartctl -a -d areca,1 /dev/sg1 smartctl 6.4 2015-06-04 r4109 [FreeBSD 9.3-RELEASE-p24 amd64] (local build) Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org do_scsi_cmnd_io with write buffer failed code = ffffffff do_scsi_cmnd_io with write buffer failed code = ffffffff do_scsi_cmnd_io with write buffer failed code = ffffffff Smartctl open device: /dev/sg1 [areca_disk#01_enc#01] failed: Input/output error **portinstall sysutils/areca-cli [#v62a3c06] # areca-cli disk info drv=01 Drive Information =============================================================== IDE Channel : 1 Model Name : Hitachi HTS723212L9A360 Serial Number : 081206FC1B00NGG Firmware Rev. : FCBOC30F Disk Capacity : 120.0GB Device State : NORMAL Timeout Count : 0 Media Error Count : 0 Device Temperature : 32 C SMART Read Error Rate : 100(62) SMART Spinup Time : 253(33) SMART Reallocation Count : 100(5) SMART Seek Error Rate : 100(67) SMART Spinup Retries : 100(60) SMART Calibration Retries : N.A.(N.A.) =============================================================== GuiErrMsg<0x00>: Success. * disc failer [#k82735e5] # areca-cli disk info drv=03 GuiErrMsg<0x12>: No Such Device. アラームが鳴動していて、No1のHDDが故障している模様。そほまま、引き抜き。 手元のSSDをボリューム削除してブランクにして、Hotなまま挿入。自動でリビルドがはじまる。 # areca-cli disk info drv=03 Drive Information =============================================================== IDE Channel : 3 Model Name : INTEL SSDSC2CT240A4 Serial Number : CVKI3201004J240 Firmware Rev. : 335u Disk Capacity : 240.1GB Device State : NORMAL Timeout Count : 0 Media Error Count : 0 Device Temperature : 255 C SMART Read Error Rate : 255(255) SMART Spinup Time : 255(255) SMART Reallocation Count : 100(0) SMART Seek Error Rate : 255(255) SMART Spinup Retries : 255(255) SMART Calibration Retries : N.A.(N.A.) =============================================================== GuiErrMsg<0x00>: Success. ---- Total access &counter(total);：本日 &counter(today);：昨日 &counter(yesterday); #counter([total|today|yesterday]);
